NPort 6400/6600 Series

Features and Benefits

  • LCD panel for easy IP address configuration (standard temp. models)
  • Secure operation modes for Real COM, TCP Server, TCP Client, Pair Connection, Terminal, and Reverse Terminal
  •  Nonstandard baudrates supported with high precision
  •  Port buffers for storing serial data when the Ethernet is offline
  •  Supports IPv6
  •  Ethernet redundancy (STP/RSTP/Turbo Ring) with network module
  •  Generic serial commands supported in Command-by-Command mode
  •  Security features based on IEC 62443

Certifications

Download Datasheet

Introduction
The NPort® 6000 is a terminal server that uses the SSL and SSH protocols to transmit encrypted serial data over Ethernet. Up to 32 serial devices of any type can be connected to the NPort® 6000, using the same IP address. The Ethernet port can be configured for a normal or secure TCP/IP connection. The NPort® 6000 secure device servers are the right choice for applications that use large numbers of serial devices packed into a small space. Security breaches are intolerable and the NPort® 6000 Series ensures data transmission integrity with support for DES, 3DES, and AES encryption algorithms. Serial devices of any type can be connected to the NPort® 6000, and each serial port on the NPort® 6000 can be configured independently for RS-232, RS-422, or RS-485 transmission.

No Data Loss If Ethernet Connection Fails
The NPort® 6000 is a reliable device server that provides users with secure serial-to-Ethernet data transmission and a customer-oriented hardware design. If the Ethernet connection fails, the NPort® 6000 will queue all serial data in its internal 64 KB port buffer. When the Ethernet connection is re-established, the NPort® 6000 will immediately release all data in the buffer in the order that it was received. Users can increase the port buffer size by installing an SD card.

LCD Panel Makes Configuration Easy
The NPort® 6600 has a built-in LCD panel for configuration. The panel displays the server name, serial number, and IP address, and any of the device server’s configuration parameters, such as IP address, netmask, and gateway address, can be updated easily and quickly.

Note: The LCD panel is only available with standard-temperature models.

Adjustable Resistor Values for RS-485 Communication
The NPort® 6600 provides adjustable termination, pull high, and pull low resistors for RS-485 communication. In some critical environments, termination resistors may be needed to prevent the reflection of serial signals, and the pull high and pull low resistors may need adjusting to maintain the integrity of the electrical signal. Since no set of resistor values works for every environment, the NPort® 6600 allows manual adjustment of the resistor values for each serial port using built-in DIP switches.

Specifications

Memory
SD Slot Up to 32 GB (SD 2.0 compatible)
Input/Output Interface
Alarm Contact Channels Resistive load: 1 A @ 24 VDC
Ethernet Interface
10/100BaseT(X) Ports (RJ45 connector) 1
Auto MDI/MDI-X connection
Magnetic Isolation Protection 1.5 kV (built-in)
Optical Fiber
100BaseFX
Multi-Mode Single-Mode
Fiber Cable Type OM1 50/125 µm G.652
800 MHz x km
Typical Distance 4 km 5 km 40 km
Wavelength Typical (nm) 1300 1310
TX Range (nm) 1260 to 1360 1280 to 1340
RX Range (nm) 1100 to 1600 1100 to 1600
Optical Power TX Range (dBm) -10 to -20 0 to -5
RX Range (dBm) -3 to -32 -3 to -34
Link Budget (dB) 12 29
Dispersion Penalty (dB) 3 1
Note: When connecting a single-mode fiber transceiver, we recommend using an attenuator to prevent damage caused by excessive optical power.
Note: Compute the “typical distance” of a specific fiber transceiver as follows: Link budget (dB) > dispersion penalty (dB) + total link loss (dB).
Ethernet Software Features
Configuration Options Web Console (HTTP/HTTPS), Serial Console, Telnet/SSH Console, Windows Utility
Management ARP, BOOTP, DHCP Client, DNS, HTTP, ICMP, IPv4/IPv6, PPPOE, SMTP, SNMPv1/v2c/v3, SNTP, TCP/IP, Telnet, UDP
Windows Real COM Drivers Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1/10 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded
Linux Real TTY Drivers Kernel versions: 2.4.x, 2.6.x, 3.x, 4.x, and 5.x
Fixed TTY Drivers SCO UNIX, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X
Android API Android 3.1.x and later
MIB MIB-II
Time Management SNTP Client
Unicast Routing RIPV1/V2, Static Route
Authentication Local Account Accessibility, RADIUS, TACACS+
Serial Inteface
Connector NPort 6600 Series: 8-pin RJ45
NPort 6450 Series: DB9 male
No. of Ports NPort 6450 Series: 4
NPort 6600-8 Series: 8
NPort 6600-16 Series: 16
NPort 6600-32 Series: 32
Serial Standard NPort 6610 Series: RS-232
NPort 6450/6650 Series: RS-232, RS-422, RS-485
Secure Operation Modes Reverse SSH, Secure Pair Connection, Secure Real COM, Secure TCP Client, Secure TCP Server, SSH
Standard Operation Modes Disabled, Ethernet Modem, Pair Connection, PPP, Printer, Real COM, Reverse Telnet, RFC2217, TCP Client, TCP Server, Terminal, UDP
Baudrate 50 bps to 921.6 kbps (supports non-standard baudrates)
Console Port NPort 6600 Series: RS-232 (TxD, RxD, GND), 8-pin RJ45 (19200, n, 8, 1)
Data Bits 5, 6, 7, 8
Stop Bits 1, 1.5, 2
Parity None, Even, Odd, Space, Mark
Flow Control RTS/CTS, DTR/DSR, XON/XOFF
RS-485 Data Direction Control NPort 6450 / 6650 Series: Supports
Pull High/Low Resistor for RS-485 NPort 6450 / 6650 Series: 1 kilo-ohm, 150 kilo-ohms
Terminator for RS-485 NPort 6450/6650 Series: 120 ohms
Serial Signals
RS-232 TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422 Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w Data+, Data-, GND
Power Parameters
Input Current NPort 6450 Series: 730 mA @ 12 VDC
NPort 6600 Series
DC Models: 293 mA @ 48 VDC, 200 mA @ 88 VDC
AC Models: 140 mA @ 100 VAC (8 ports), 192 mA @ 100 VAC (16 ports), 285 mA @ 100 VAC (32 ports)
Input Voltage NPort 6450 Series: 12 to 48 VDC
NPort 6600 Series
AC Models: 100 to 240 VAC
DC Models: ±48 VDC (20 to 72 VDC, -20 to -72 VDC), 110 VDC (88 to 300 VDC)
Reliability
Automatic Reboot Trigger Built-in WDT
Alert Tools Built-in buzzer and RTC (real-time clock)
Physical Characteristics
Housing Metal
Dimensions (with ears) NPort 6450 Series: 181 x 103 x 35 mm (7.13 x 4.06 x 1.38 in)
NPort 6600 Series: 480 x 195 x 44 mm (18.9 x 7.68 x 1.73 in)
Dimensions (without ears) NPort 6450 Series: 158 x 103 x 35 mm (6.22 x 4.06 x 1.38 in)
NPort 6600 Series: 440 x 195 x 44 mm (17.32 x 7.68 x 1.73 in)
Weight NPort 6450 Series: 1,020 g (2.25 lb)
NPort 6600-8 Series: 3,460 g (7.63 lb)
NPort 6600-16 Series: 3,580 g (7.89 lb)
NPort 6600-32 Series: 3,600 g (7.94 lb)
Interactive Interface LCD panel display (non-T models only)
Push buttons for configuration (non-T models only)
Installation NPort 6450 Series: Desktop, DIN-rail mounting, Wall mounting
NPort 6600 Series: Rack mounting (with optional kit)
Environmental Limits
Operating Temperature Standard Models: 0 to 55°C (32 to 131°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
High-Voltage Wide Temp. Models: -40 to 85°C (-40 to 185°F)
Storage Temperature (package included) Standard/Wide Temp. Models: -40 to 75°C (-40 to 167°F)
High-Voltage Wide Temp. Models: -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity 5 to 95% (non-condensing)
Standard and Cerifications
EMC EN 55032/24
EMI CISPR 32, FCC Part 15B Class A
EMS NPort 6450 Series:
IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power: 1 kV; Signal: 0.5 kV
IEC 61000-4-5 Surge: Power: 1 kV; Signal: 1 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 3 V/m; Signal: 3 V/m
IEC 61000-4-8 PFMF
IEC 61000-4-11 DIPs
NPort 6600 Series (except -48V/-HV models):
IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power 1 kV; Signal 0.5 kV
IEC 61000-4-5 Surge: Power: 2 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 3 V/m; Signal: 3 V/m
IEC 61000-4-8 PFMF
IEC 61000-4-11 DIPs
NPort 6600-48V Series:
IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power: 1 kV; Signal: 0.5 kV
IEC 61000-4-5 Surge: Power: 1 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 3 V/m; Signal: 3 V/m
IEC 61000-4-8 PFMF
NPort 6650-HV Series:
IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power: 4 kV; Signal: 2 kV
IEC 61000-4-5 Surge: Power: 2 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 3 V/m; Signal: 3 V/m
IEC 61000-4-8 PFMF
Traffic Control NEMA TS2
Safety UL 60950-1
Vibration IEC 60068-2-6
Freefall IEC 60068-2-34
Declaration
Green Product RoHS, CRoHS, WEEE
MTBF
Time NPort 6450 Series: 850,905 hrs
NPort 6610-8 Series: 135,891 hrs
NPort 6610-16 Series: 102,373 hrs
NPort 6610-32 Series: 68,707 hrs
NPort 6650-8 Series: 636,600 hrs
NPort 6650-16 Series: 439,673 hrs
NPort 6650-32 Series: 310,078 hrs
NPort 6650-8-HV-T: 501,171 hrs
NPort 6650-16-HV-T: 380,006 hrs
NPort 6650-32-HV-T: 290,914 hrs
Standards NPort 6450 Series: Telcordia (Bellcore) Standard TR/SR
NPort 6600 Series: Telcordia (Bellcore) Standard
Warranty
Warranty Period 5 years
Details See www.moxa.com/warranty