NPort 5600-DT Series

Features and Benefits

  •  8 serial ports supporting RS-232/422/485
  • Compact desktop design
  •  10/100M auto-sensing Ethernet
  •  Easy IP address configuration with LCD panel
  •  Configure by Telnet, web browser, or Windows utility
  •  Socket modes: TCP server, TCP client, UDP, Real COM
  •  SNMP MIB-II for network management

Certifications

Download Datasheet

Introduction
NPort 5600-8-DT device servers can conveniently and transparently connect 8 serial devices to an Ethernet network, allowing you to network your existing serial devices with only basic configuration. You can both centralize management of your serial devices and distribute management hosts over the network. Since the NPort 5600-8-DT device servers have a smaller form factor compared to our 19-inch models, they are a great choice for applications that need additional serial ports, but for which mounting rails are not available.

Convenient Design for RS-485 Applications
The NPort 5650-8-DT device servers support selectable 1 kilo-ohm and 150 kilo-ohms pull high/low resistors and a 120-ohm terminator. In some critical environments, termination resistors may be needed to prevent the reflection of serial signals. When using termination resistors, it is also important to set the pull high/low resistors correctly so that the electrical signal is not corrupted. Since no set of resistor values is universally compatible with all environments, NPort 5600-8-DT device servers use DIP switches to allow users to adjust termination and pull high/low resistor values manually for each serial port.

Convenient Power Inputs
The NPort 5650-8-DT device servers support both power terminal blocks and power jacks for ease of use and greater flexibility. Users can connect the terminal block directly to a DC power source, or use the power jack to connect to an AC circuit through an adapter.

LED Indicators to Ease Your Maintenance Tasks
The System LED, Serial Tx/Rx LEDs, and Ethernet LEDs (located on the RJ45 connector) provide a great tool for basic maintenance tasks and help engineers analyze problems in the field. The NPort 5600’s LEDs not only indicate current system and network status, but also help field engineers monitor the status of attached serial devices.

Two Ethernet Ports for Convenient Cascade Wiring
The NPort 5600-8-DT device servers come with two Ethernet ports that can be used as Ethernet switch ports. Connect one port to the network or server, and the other port to another Ethernet device. The dual Ethernet ports eliminate the need to connect each device to a separate Ethernet switch, reducing wiring costs.

Appearance

Specifications

Ethernet Interface
10/100BaseT(X) Ports (RJ45 connector) 2
Magnetic Isolation Protection 1.5 kV (built-in)
Ethernet Software Features
Configuration Options Serial Console, Telnet Console, Web Console (HTTP/HTTPS), Windows Utility
Management ARP, BOOTP, DHCP Client, DNS, HTTP, HTTPS, ICMP, IPv4, LLDP, Rtelnet, SMTP, SNMPv1/v2c, TCP/IP, Telnet, UDP
Filter IGMP v1/v2
Windows Real COM Drivers Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1/10 (x86/x64), Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP Embedded
Linux Real TTY Drivers Kernel versions: 2.4.x, 2.6.x, 3.x, 4.x, and 5.x
Fixed TTY Drivers SCO UNIX, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.x, HP-UX 11i, Mac OS X
Android API Android 3.1.x and later
MIB RFC1213, RFC1317
Time Management SNTP
Serial Inteface
Connector 8-pin RJ45:
NPort 5610-8-DT-J/5650-8-DT-J
DB9 male:
NPort 5610-8-DT models/NPort 5650-8-DT models/NPort 5650I-8-DT models
No. of Ports 8
Serial Standard NPort 5610-8-DT Series: RS-232
NPort 5650-8-DT Series: RS-232/422/485
Baudrate Supports standard baudrates (unit=bps): 50, 75, 110, 134, 150, 300, 600, 1200, 1800, 2400, 4800, 7200, 9600, 19200, 38400, 57600, 115200, 230.4k, 460.8k, 921.6k
Data Bits 5, 6, 7, 8
Stop Bits 1, 1.5, 2
Parity None, Even, Odd, Space, Mark
Flow Control RTS/CTS, DTR/DSR, XON/XOFF
Pull High/Low Resistor for RS-485 1 kilo-ohm, 150 kilo-ohms
RS-485 Data Direction Control ADDC® (automatic data direction control)
Terminator for RS-485 120 ohms
Isolation -I models: 2 kV
Surge 0.5 kV
Console Port RS-232 (TxD, RxD, GND), 3-pin (19200, n, 8, 1)
Serial Signals
RS-232 TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
RS-422 Tx+, Tx-, Rx+, Rx-, GND
RS-485-4w Tx+, Tx-, Rx+, Rx-, GND
RS-485-2w Data+, Data-, GND
Power Parameters
Input Current NPort 5610-8-DT/NPort 5610-8-DT-J/NPort 5610-8-DT-T: 611 mA @ 12 VDC
NPort 5650-8-DT/NPort 5650-8-DT-J/NPort 5650-8-DT-T: 615 mA @ 12 VDC
NPort 5650I-8-DT/NPort 5650I-8-DT-T: 1066 mA @ 12 VDC
Input Voltage 12 to 48 VDC
No. of Power Inputs 2
Reverse Polarity Protection Supported
Reliability
Automatic Reboot Trigger Built-in WDT
Alert Tools Built-in buzzer and RTC (real-time clock)
Physical Characteristics
Housing Metal
Dimensions (with ears) 229 x 46 x 125 mm (9.01 x 1.81 x 4.92 in)
Dimensions (without ears) 197 x 44 x 125 mm (7.76 x 1.73 x 4.92 in)
Dimensions (with DIN-rail kit on bottom panel) 197 x 53 x 125 mm (7.76 x 2.09 x 4.92 in)
Weight NPort 5610-8-DT: 1,570 g (3.46 lb)
NPort 5610-8-DT-J: 1,520 g (3.35 lb)
NPort 5610-8-DT-T: 1,320 g (2.91 lb)
NPort 5650-8-DT: 1,590 g (3.51 lb)
NPort 5650-8-DT-J: 1,540 g (3.40 lb)
NPort 5650-8-DT-T: 1,340 g (2.95 lb)
NPort 5650I-8-DT: 1,660 g (3.66 lb)
NPort 5650I-8-DT-T: 1,410 g (3.11 lb)
Interactive Interface LCD panel display
Push buttons for configuration
Installation Desktop, DIN-rail mounting (with optional kit), Wall mounting (with optional kit)
Environmental Limits
Operating Temperature Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature (package included) -40 to 75°C (-40 to 167°F)
Ambient Relative Humidity 5 to 95% (non-condensing)
Standard and Cerifications
EMC EN 55032/35
EMI CISPR 32, FCC Part 15B Class A
EMS IEC 61000-4-2 ESD: Contact: 6 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power: 2 kV; Signal: 0.5 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 0.5 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 3 V/m; Signal: 3 V/m
IEC 61000-4-8 PFMF
IEC 61000-4-11
Safety UL 60950-1, IEC 62368-1
Declaration
Green Product RoHS, CRoHS, WEEE
MTBF
Time 836,374 hrs
Standards Telcordia (Bellcore) Standard
Warranty
Warranty Period 5 years
Details See www.moxa.com/warranty