ioLogik E1200 Series

Features and Benefits

  • User-definable Modbus TCP Slave addressing
  • Supports EtherNet/IP Adapter mode
  • Supports RESTful API for IIoT applications
  • 2-port Ethernet switch for daisy-chain topologies
  • Saves time and wiring costs with peer-to-peer communications
  • Active communication with MX-AOPC UA Server
  • Supports SNMP v1/v2c
  • Easy mass deployment and configuration with ioSearch utility
  • Friendly configuration via web browser
  • Simplifies I/O management with MXIO library for Windows or Linux
  • Class I Division 2, ATEX Zone 2 certification
  • Wide operating temperature models available for -40 to 75°C (-40 to 167°F) environments


Download Datasheet


The ioLogik E1200 Series supports the most often-used protocols for retrieving I/O data, making it capable of handling a wide variety of applications. Most IT engineers use SNMP or RESTful API protocols, but OT engineers are more familiar with OT-based protocols, such as Modbus and EtherNet/IP. Moxa’s Smart I/O makes it possible for both IT and OT engineers to conveniently retrieve data from the same I/O device. The ioLogik E1200 Series speaks six different protocols, including Modbus TCP, EtherNet/IP, and Moxa AOPC for OT engineers, as well as SNMP, RESTful API, and Moxa MXIO library for IT engineers. The ioLogik E1200 retrieves I/O data and converts the data to any of these protocols at the same time, allowing you to get your applications connected easily and effortlessly.

Daisy-Chained Ethernet I/O Connection

This industrial Ethernet remote I/O comes with two switched Ethernet ports to allow for the free flow of information downstream to another local Ethernet device, or upstream to a control server via expandable daisy-chained Ethernet I/O arrays. Applications such as factory automation, security and surveillance systems, and tunneled connections can make use of daisy-chained Ethernet for building multidrop I/O networks over standard Ethernet cables. Many industrial automation users are familiar with multidrop as the configuration most typically used in fieldbus solutions. The daisy-chain capabilities supported by ioLogik Ethernet remote I/O units not only increase the expandability and installation possibilities for your remote I/O applications, but also lower overall costs by reducing the need for separate Ethernet switches. Daisy-chaining devices in this way will also reduce overall labor and cabling expenses.

Save Time and Wiring Costs with Peer-to-Peer Communications

In remote automation applications, the control room and sensors are often far removed, making wiring over long distances a constant challenge. With peer-to-peer networking, users may now map a pair of ioLogik Series modules so that input values will be directly transferred to output channels, greatly simplifying the wiring process and reducing wiring costs.

User-Definable Modbus TCP Addressing for Painless Upgrading of Existing Systems

For Modbus devices that are controlled and detected by fixed addresses, users need to spend a vast amount of time researching and verifying initial configurations. Users need to locate each device’s networking details, such as I/O channels or vendor-defined addresses, to enable the initial or start address of a SCADA system or PLC. Devices that support user-definable Modbus TCP addressing offer greater flexibility and easier setup. Instead of worrying about individual devices, users simply configure the function and address map to fit their needs.

Push Technology for Events

When used with MX-AOPC UA Server, devices can use active push communications when communicating changes in state and/or events to a SCADA system. Unlike a polling system, when using a push architecture for communications with a SCADA system, messages will only be delivered when changes in state or configured events occur, resulting in higher accuracy and lower amounts of data that need to be transferred.


Input/Output Interface
Analog Input Channels ioLogik E1240 models: 8
ioLogik E1242 models: 4
Analog Output Channels ioLogik E1241 models: 4
Configurable DIO Channels (by jumper) ioLogik E1212 models: 8
ioLogik E1213/E1242 models: 4
Digital Input Channels ioLogik E1210 models: 16
ioLogik E1212/E1213 models: 8
ioLogik E1214 models: 6
ioLogik E1242 models: 4
Digital Output Channels ioLogik E1211 models: 16
ioLogik E1213 models: 4
Isolation 3k VDC or 2k Vrms
Relay Channels ioLogik E1214 models: 6
RTD Channels ioLogik E1260 models: 6
Thermocouple Channels ioLogik E1262 models: 8
Buttons Reset button
Digital Inputs
Connector Screw-fastened Euroblock terminal
Counter Frequency 250 Hz
Digital Filtering Time Interval Software configurable
Dry Contact On: short to GND
Off: open
I/O Mode DI or event counter
Points per COM ioLogik E1210/E1212 models: 8 channels
ioLogik E1213 models: 12 channels
ioLogik E1214 models: 6 channels
ioLogik E1242 models: 4 channels
Sensor Type Dry contact
Wet contact (NPN or PNP)
Wet Contact (DI to COM) On: 10 to 30 VDC
Off: 0 to 3 VDC
Digital Outputs
Connector Screw-fastened Euroblock terminal
Current Rating ioLogik E1211/E1212/E1242 models: 200 mA per channel
ioLogik E1213 models: 500 mA per channel
I/O Mode DO or pulse output
I/O Type ioLogik E1211/E1212/E1242 models: Sink
ioLogik E1213 models: Source
Over-Current Protection ioLogik E1211/E1212/E1242 models: 2.6 A per channel @ 25°C
ioLogik E1213 models: 1.5 A per channel @ 25°C
Over-Temperature Shutdown 175°C (typical), 150°C (min.)
Over-Voltage Protection 35 VDC
Pulse Output Frequency 500 Hz (max.)
Breakdown Voltage 500 VAC
Connector Screw-fastened Euroblock terminal
Contact Current Rating Resistive load: 5 A @ 30 VDC, 250 VAC, 110 VAC
Contact Resistance 100 milli-ohms (max.)
Electrical Endurance 100,000 operations @ 5 A resistive load
Initial Insulation Resistance 1,000 mega-ohms (min.) @ 500 VDC
Mechanical Endurance 5,000,000 operations
Pulse Output Frequency 0.3 Hz at rated load (max.)
Type Form A (N.O.) power relay
Note Ambient humidity must be non-condensing and remain between 5 and 95%. The relays may malfunction when operating in high condensation environments below 0°C.
Analog Inputs
Accuracy ioLogik E1240/E1242:
±0.1% FSR @ 25°C
±0.3% FSR @ -10 to 60°C
ioLogik E1240-T/E1242-T:
±0.1% FSR @ 25°C
±0.3% FSR @ -10 to 60°C
±0.5% FSR @ -40 to 75°C
Built-in Resistor for Current Input 120 ohms
Connector Screw-fastened Euroblock terminal
I/O Mode Voltage/Current
I/O Type Differential
Input Impedance 10 mega-ohms (min.)
Input Range 0 to 10 VDC
0 to 20 mA
4 to 20 mA
4 to 20 mA (with burn-out detection)
Resolution 16 bits
Sampling Rate ioLogik E1240: 12 samples/sec per module (shared between up to 8 channels)
ioLogik E1242: 12 samples/sec per module (shared between up to 4 channels)
Analog Outputs
Accuracy ioLogik E1241:
±0.1% FSR @ 25°C
±0.3% FSR @ -10 to 60°C
ioLogik E1241-T:
±0.1% FSR @ 25°C
±0.3% FSR @ -40 to 75°C
Connector Screw-fastened Euroblock terminal
Voltage Output Short-Circuit Protection 10 mA
Internal Resistor 400 ohms
Note: 24 V of external power required when loading exceeds 1000 ohms
Output Range 0 to 10 VDC
4 to 20 mA
Resolution 12-bit
Accuracy ioLogik E1260:
±0.1% FSR @ 25°C
±0.3% FSR @ -10 to 60°C
ioLogik E1260-T:
±0.1% FSR @ 25°C
±0.3% FSR @ -40 to 75°C
Connector Screw-fastened Euroblock terminal
Input Connection 2- or 3-wire
Input Impedance 625 kilo-ohms (min.)
Sensor Type PT1000 (-200 to 350°C)
PT50, PT100, PT200, PT500 (-200 to 850°C)
Resistance Type 310, 620, 1250, and 2200 ohms
Resolution 0.1°C or 0.1 ohms
Sampling Rate ioLogik E1260: 12 samples/sec per module (shared between up to 6 channels)
Millivolt Accuracy ioLogik E1262:
±0.1% FSR @ 25°C
±0.3% FSR @ -10 to 60°C
ioLogik E1262-T:
±0.1% FSR @ 25°C
±0.3% FSR @ -40 to 75°C
Connector Screw-fastened Euroblock terminal
TC Accuracy Types J, T, E, S, B: ±5°C
Types K, R, N: ±8°C
CJC Accuracy ±0.5°C @ 25°C
±1.5°C @ -40 to 75°C
Input Impedance 10 mega-ohms (min.)
Millivolt Type ±19.532 mV
±39.062 mV
±78.126 mV
Fault and over-voltage protection: -35 to +35 VDC (power off); -25 to +30 VDC (power on)
Resolution 16 bits
Sampling Rate ioLogik E1262: 12 samples/sec per module (shared between up to 8 channels)
Sensor Type J, K, T, E, R, S, B, N
Ethernet Interface
10/100BaseT(X) Ports (RJ45 connector) 2, 1 MAC address (Ethernet bypass)
Magnetic Isolation Protection 1.5 kV (built-in)
Ethernet Software Features
Configuration Options Web Console (HTTP), Windows Utility (ioSearch)
Industrial Protocols EtherNet/IP Adapter, Modbus TCP Server (Slave), Moxa AOPC (Active Tag), MXIO Library
Management BOOTP, RESTful API, DHCP Client, HTTP, IPv4, TCP/IP, UDP, SNMPv1 Trap, SNMPv1/v2c
MIB Device Settings MIB
Security Access control list
LED Interface
LED Indicators Power, Ready, Port 1, Port 2
Modbus TCP
Functions Supported 1, 2, 3, 4, 5, 6, 15, 16, 23
Mode Server (Slave)
Max. No. of Client Connections 10
Mode Adapter
Max. No. of Scanner Connections 9 (for read-only), 1 (for read/write)
Power Parameters
Power Connector Screw-fastened Euroblock terminal
No. of Power Inputs 1
Input Voltage 12 to 36 VDC
Power Consumption ioLogik E1210 Series: 110 mA @ 24 VDC
ioLogik E1211 Series: 200 mA @ 24 VDC
ioLogik E1212 Series: 155 mA @ 24 VDC
ioLogik E1213 Series: 130 mA @ 24 VDC
ioLogik E1214 Series: 188 mA @ 24 VDC
ioLogik E1240 Series: 121 mA @ 24 VDC
ioLogik E1241 Series: 194 mA @ 24 VDC
ioLogik E1242 Series: 139 mA @ 24 VDC
ioLogik E1260 Series: 110 mA @ 24 VDC
ioLogik E1262 Series: 118 mA @ 24 VDC
Physical Characteristics
Housing Plastic
Dimensions 27.8 x 124 x 84 mm (1.09 x 4.88 x 3.31 in)
Weight 200 g (0.44 lb)
Installation DIN-rail mounting, Wall mounting
Wiring I/O cable, 16 to 26 AWG
Power cable, 12 to 24 AWG
Environmental Limits
Operating Temperature Standard Models: -10 to 60°C (14 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature (package included) -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity 5 to 95% (non-condensing)
Altitude 4000 m
Standards and Certifications
EMC EN 55032/24, EN 61000-6-2/-6-4
EMI CISPR 32, FCC Part 15B Class A
EMS IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 10 V/m
IEC 61000-4-4 EFT: Power: 2 kV; Signal: 1 kV
IEC 61000-4-5 Surge: Power: 2 kV; Signal: 1 kV
IEC 61000-4-6 CS: 10 V
IEC 61000-4-8 PFMF
Hazardous Locations ATEX, Class I Division 2
Safety UL 508
Shock IEC 60068-2-27
Freefall IEC 60068-2-32
Vibration IEC 60068-2-6
Green Product RoHS, CRoHS, WEEE
Time ioLogik E1210 Series: 671,345 hrs
ioLogik E1211 Series: 923,027 hrs
ioLogik E1212 Series: 561,930 hrs
ioLogik E1213 Series: 715,256 hrs
ioLogik E1214 Series: 808,744 hrs
ioLogik E1240 Series: 474,053 hrs
ioLogik E1241 Series: 888,656 hrs
ioLogik E1242 Series: 502,210 hrs
ioLogik E1260 Series: 660,260 hrs
ioLogik E1262 Series: 631,418 hrs
Standards Telcordia SR332
Warranty Period ioLogik E1214: 2 years
ioLogik E1210/E1211/E1212/E1213/E1240/E1241/E1242/E1260/E1262: 5 years
Details See